Skip to main content
How can we help?

Squelch, Gain & Filters

Below the scan source on the Scanner tab are four small cards: Squelch & Gain, Detection, Sound and AM only. Everything on them applies live while scanning, except Auto gain, which applies the next time you press Start.

Squelch & Gain

  • Squelch — how far over the noise a signal must be, in dB, before the scanner stops on it and plays it (3–25 dB). The noise is measured on the channel itself, so the number means the same on any radio and any band: an empty channel reads about 0 dB. Around 6–8 dB suits most listening; very low settings stop on noise more often.
  • Auto (beside the squelch value) — the scanner sets its own stop level. It starts at 8 dB, goes up a little each time a stop turns out to be noise, and comes back down after two quiet minutes, staying between 5 and 15 dB. It settles at the lowest level that keeps noise stops rare on your radio, aerial and band. With Auto on, the slider becomes a tweak from −6 to +6 dB: left stops on weaker signals (and a little more noise), right only on stronger ones. The value beside it shows the level in use, for example A 9.0.
  • A channel of its own — the squelch is one setting for the whole scan, but any channel in a scan list can be tweaked up or down with its Sq ± column (see The Scan Lists Tab).
  • Gain — the radio’s sensitivity (0–100%). More is not always better: past a point the noise rises as fast as the signals, and strong local transmitters start to overload the radio. To find the best setting, tune a steady signal such as an airfield ATIS and raise the gain until it stops getting clearer; on one Airspy R2 on an outdoor aerial that was about 70%. Changing the gain while scanning takes effect straight away; the scanner re-measures the noise on every channel as it changes.
  • Auto gain — the radio’s own automatic gain control sets the gain instead (applies on Start).
  • FM noise squelch — on NFM channels, the squelch opens only when a real FM carrier quiets the receiver’s hiss, not just on signal strength. It stops the scanner sitting on noise, intermodulation and splatter. A carrier from about 6 dB over the noise opens it, as on a handheld scanner.

Detection

  • Voice detection — the scanner only stays on speech, skipping birdies, data carriers and plain noise. Sensitivity trades strictness (left: never noise, may skip a weak voice) against looseness (right: catches all voice, may grab some noise).
  • Hold — how long to stay on a channel after the signal drops before carrying on scanning (0.5–10 seconds), so a reply isn’t missed.
  • Max hold — a hard limit, in seconds, on how long the scanner ever stays on one channel.
  • Lock noise after N — once a channel has been rejected as noise this many times, it goes on the session’s temporary lockouts (see Auto-Lockout & Managing Lockouts).

Sound

  • Volume, with L and R — play this profile in the left or right ear only (press again for both). With two profiles on, put one left and the other right to tell them apart.
  • Speech filter — keeps the speech range (300–3400 Hz) and lifts it slightly for clarity, cutting hum, rumble and repeater tones below and hiss above. On NFM it also undoes the transmitter’s treble boost, for natural voices and less hiss.
  • Noise reduction, with Strength — takes the hiss off the voice while leaving the speech alone. Gentle settings sound natural; strong ones take more hiss out between words but can sound processed.

AM only

  • Noise blanker — takes out static clicks (ignition, power lines, radar) before the signal is demodulated.
  • Notch — removes steady whistles, such as a neighbouring carrier beating against this one.
  • Leveller — brings weak and strong calls to one volume. It affects the speaker only; recordings keep their level.
  • Sync AM — a synchronous AM detector that locks to the carrier: cleaner weak calls and less distortion on fades. On offset-carrier (“climax”) channels, where several transmitters a few kHz apart send the same audio, it switches to the normal detector by itself, so it is safe to leave on.

How the scanner spots weak AM calls

An AM signal keeps most of its power in its carrier, a narrow line in the middle of the channel. While sweeping, the scanner looks for the strongest 2 kHz part of each AM channel rather than the whole channel, which takes in about a quarter of the noise, so weaker airband calls are caught. On channels spaced 25 kHz apart it searches a wider span, so offset (“climax”) carriers a few kHz either side of the channel are found too. None of this needs setting up.

Table of Contents
Scroll to Top
Loading...
Loading...
Loading...
Loading...
Loading...

Contact Us

Couldn't find what you were looking for?

Our support team is here to help. Reach out and we'll respond as soon as possible.